How the Fleck Arsenic Filter Treats Arsenic in Household Water
When arsenic is detected in water, treatment technology like the Fleck Arsenic Filter is designed to reduce arsenic concentrations by targeting the contaminant at the point where water enters the home system. This equipment uses a filtration process tailored specifically to capture arsenic particles, helping protect household water quality. The Fleck System ships ready to configure for residential water treatment and can help households regain water safety and clarity after previous equipment has failed.
Scope and Limitations of Area Sampling Data for Arsenic
Government data from the U.S. Geological Survey sampled groundwater from four wells in Whatcom County’s aquifer labeled 112GLCV. These samples, taken between October 2010 and August 2018, show arsenic concentrations ranging from 0.12 to 0.72 micrograms per liter, with a median of 0.14 micrograms per liter. All sampled wells were between 22 and 98 feet deep. None of the results exceeded federal arsenic thresholds, indicating the data reflect typical conditions in the aquifer area rather than any individual well. Since the sample size is small—only six samples—the data provide a limited but useful snapshot of regional arsenic presence. Actual arsenic levels in any individual household water supply must be confirmed with a dedicated test of that water.
Household Signs That May Indicate Arsenic Presence or Other Issues
Arsenic in water is generally not detectable by taste, smell, or appearance, so household symptoms are unlikely to directly signal its presence. Equipment failure might be noticed if water treatment devices no longer function properly, but this does not confirm arsenic levels. Since arsenic is odorless and tasteless, no staining or discoloration on plumbing fixtures commonly associates with it. Households suspecting arsenic should consider testing even if water appears normal, especially after treatment equipment malfunctions.
Stepwise Approach to Excluding Common Causes Before Testing for Arsenic
Before arranging a certified laboratory test for arsenic, it is helpful to rule out other water quality problems that might cause visible or taste-related issues. Check for sediment buildup, changes in water pressure, or equipment malfunctions that could affect water performance. If these are ruled out and arsenic concerns remain due to regional data or equipment failure, the next step is to collect a representative water sample for laboratory analysis focused on arsenic content.
Understanding a Certified Laboratory Arsenic Test Report
A certified laboratory report will provide arsenic concentrations in micrograms per liter (ug/L), quantitatively indicating the element’s presence in the tested water. Since arsenic detection below federal thresholds is common in this region, the exact number must be compared to the regulatory limits established by agencies such as the EPA. The report will also outline the analytical methods and detection limits used, helping homeowners interpret the results accurately. Only a test specific to your household water can establish your arsenic level with certainty.
Long-Term Implications of Untreated Arsenic in Water
Continuous exposure to elevated arsenic levels in drinking water can pose health concerns over many years. While the government sampling in aquifer 112GLCV shows no exceedance of thresholds, untreated arsenic in water at higher concentrations can increase health risks, warranting effective filtration. Using a dedicated treatment system like the Fleck Arsenic Filter can reduce arsenic exposure, supporting sustained household water safety.
In summary, government data provide a regional view of arsenic presence in Whatcom County’s aquifer 112GLCV but cannot specify individual household levels. Testing your own water is essential after equipment failure. The Fleck Arsenic Filter offers a proven option to address arsenic if testing confirms the need for treatment.
Where this information comes from
Source: USGS groundwater sampling. Sampled 2018-08-07. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.
On record: U.S. Geological Survey sampling of Arsenic in the 112GLCV aquifer (Whatcom County): 6 results from 4 wells, median 0.14 ug/L, range 0.12-0.72 ug/L; none above any federal threshold
- ✓ 90-Day Money-BackNo restocking fees — return within 90 days.
- ✓ Manufacturer WarrantyGenuine Fleck · Pentair · VIQUA equipment.
- ✓ Free Expert SizingTalk to a specialist and buy the right system the first time.