Sizing Total Well Water Treatment for Households in CT with Aquifer 112DFSF
$1,375.00
WSP Whole House Nitrate Reduction System - Well Water, Nitrite Removal
✓ Free shipping in the USA · ✓ 90-day returns · ✓ Secure checkout
Write Down Your Household Water Use and Current Well Details Before Seeking Treatment Advice
When considering total well water treatment, start by documenting your household's daily water demand in gallons per day along with any fluctuations due to occupancy or outdoor water use. Record the depth and source of your well if known. Note any water quality test results specific to your well—especially those from a certified laboratory that include chloride and total dissolved solids measurements. This information is essential to determining the appropriate treatment system size and configuration.
If You Notice Rapid Fixture or Appliance Wear, Inspect for Elevated Dissolved Solids Effects
Fixtures like faucets and showerheads, and appliances such as water heaters, ice makers, and dishwashers, may show scale buildup, staining, or corrosion first in the presence of elevated chloride or total dissolved solids. These issues arise because elevated dissolved solids can lead to mineral deposits and metal leaching. Tracking which fixtures exhibit symptoms helps confirm whether total well water treatment is needed and guides system sizing to address the volume and severity of these impacts.
Evaluate Your Daily Water Usage Against Treatment Capacity to Size Correctly
The total well water treatment equipment, such as the Fleck Total Well Chlorination System with a grain capacity of 32,000, must match your household's water demand for effective results. Grain capacity generally refers to the system's ability to handle a given amount of dissolved solids before regeneration or maintenance is needed. Compare your documented daily water usage to the treatment system's capacity to ensure it can treat water adequately without frequent recovery downtime. Choosing a system with appropriate capacity helps maintain water quality consistently.
If You Experience Water Taste or Staining but No Health Issues, Consider Treatment Accordingly
Households may observe taste changes or staining on fixtures, which can result from chloride concentrations exceeding secondary standards in the local aquifer. The U.S. Geological Survey data for Connecticut's Aquifer 112DFSF shows a median chloride level of 66.65 mg/L, with some wells reaching up to 875 mg/L. Four samples were above the secondary aesthetic standard of 250 mg/L. These findings indicate potential aesthetic issues but do not imply health risks. Treatment decisions should focus on addressing these aesthetic or operational concerns rather than safety alone.
Understand That Regional Chloride Concentrations Reflect Area Trends, Not Individual Well Conditions
The U.S. Geological Survey's regional sampling of 24 results from 20 wells (2011-2017) provides a valuable reference for Aquifer 112DFSF in Connecticut. However, these measurements represent area trends, not the exact conditions of any single well. Chloride was detected in every sample, ranging widely, but detection alone does not indicate a violation or safety issue. Testing your own well water through accredited laboratories is necessary to confirm specific conditions and tailor treatment accordingly.
Recognize the Difference Between Public Water System Records and Private Well Testing
Public water system records typically include regular testing data and compliance results, often available to consumers. In contrast, private well water quality must be established by direct testing of the individual’s well water, as local groundwater sampling data cannot substitute for this. The regional data for Aquifer 112DFSF is informative but should not replace private well analysis when selecting and sizing a water treatment system.
Summary: Regional chloride data for Connecticut's FIPS 110 Aquifer 112DFSF area is based on sampling of 20 separate wells from 2011 to 2017. For detailed data, see the U.S. Geological Survey groundwater monitoring page. Properly sizing total well water treatment systems requires household water use data, specific well tests, and understanding the scope and limits of regional water quality information.
Where this information comes from
Source: USGS groundwater sampling. Sampled 2017-09-05. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.
On record: U.S. Geological Survey sampling of Chloride in the 112DFSF aquifer (FIPS 110): 24 results from 20 wells, median 66.65 mg/L, range 1.47-875.0 mg/L; 4 above an AESTHETIC secondary standard only (secondary standard 250.0 mg/L (aesthetic)) - not a health finding