Government Sampling Records and Corrosive Water Indicators
Government sampling conducted by the U.S. Geological Survey in the aquifer known as 112DFSF within Connecticut's FIPS 180 area collected 69 chloride results from 19 separate wells between 2015 and 2025. These wells were between 10 and 80 feet deep. The data show that chloride was detected in all samples, with a median concentration of 212 mg/L and a range from 4.69 to 3620 mg/L. This information provides a regional snapshot of water constituents that can influence corrosivity but does not indicate the condition of any specific household's water.
Why Aesthetic Secondary Standards Differ from Health-Based Limits for Chloride
Chloride has a secondary standard set at 250 mg/L established for aesthetic reasons such as taste, staining, and corrosion potential, not for health safety. In this sampling, 28 results exceeded this aesthetic benchmark, but this does not signify a health risk or violation. Understanding this distinction is important because treatment decisions should not be based solely on chlorides surpassing aesthetic thresholds, but rather on the overall impact on plumbing and water quality experienced at the tap.
A Worked Example: Interpreting Median and Range for a Household
Consider a household drawing from this area: the median chloride value of 212 mg/L lies below the aesthetic limit, but the range extends well beyond it, up to 3620 mg/L. This suggests that water corrosivity and potential pipe damage risks can vary widely depending on exact well characteristics and location. Therefore, a homeowner's water may or may not have levels of constituents that contribute to corrosion as observed in regional sampling.
Information You Should Record Before Consulting on Treatment Options
Before exploring treatment solutions, it is essential to obtain specific water testing from a certified laboratory for your household’s well or source. Key details to note include:
- Chloride concentration in mg/L
- pH level
- Water hardness and total dissolved solids
- Any visible signs of staining, taste changes, or plumbing corrosion
This data will help clarify if corrosive conditions exist and to what degree, enabling informed equipment choice.
How Water Quality Changes After Using the Fleck Corrosive Water Damaging Pipes Filter
When configured, the Fleck Corrosive Water Damaging Pipes Filter acts to reduce water corrosivity. It modifies water chemistry to protect household piping, mitigating damage mechanisms associated with high chloride and related factors. Treated water at the tap typically shows less corrosive potential, which can help preserve plumbing longevity and improve water aesthetic qualities.
Additional Considerations Commercial or Industrial Operators Add
While a household focuses primarily on protecting plumbing and taste, commercial or industrial users often evaluate:
- System-wide corrosion control over large volumes
- Compliance with regulatory requirements and monitoring programs
- Impact on equipment beyond pipes, such as boilers and cooling towers
- Operational costs and maintenance scheduling for treatment systems
These factors extend considerations beyond the household scale and influence treatment system selection and design.
Reading a Certified Laboratory Report for Chloride and Corrosivity
A laboratory report for chloride will list exact concentrations in mg/L, with detection limits and analytical method details. It will not declare safety or violations but provides data to assess corrosive tendencies. Paired with pH and other parameters, this report helps confirm if corrosive water treatment is advisable.
Overall, a certified test of your specific water source is essential for evaluation rather than relying on regional data alone.
Finally, the USGS records cited here summarize groundwater chloride data for aquifer 112DFSF in Connecticut’s FIPS 180, offering a regional perspective accessible at https://waterdata.usgs.gov/monitoring-location/413200071531101/.
Where this information comes from
Source: USGS groundwater sampling. Sampled 2025-11-21. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.
On record: U.S. Geological Survey sampling of Chloride in the 112DFSF aquifer (FIPS 180): 69 results from 19 wells, median 212.0 mg/L, range 4.69-3620.0 mg/L; 28 above an AESTHETIC secondary standard only (secondary standard 250.0 mg/L (aesthetic)) - not a health finding
- ✓ 90-Day Money-BackNo restocking fees — return within 90 days.
- ✓ Manufacturer WarrantyGenuine Fleck · Pentair · VIQUA equipment.
- ✓ Free Expert SizingTalk to a specialist and buy the right system the first time.