Choosing the right size for a complete well water treatment system is the key decision this week for Pitt County homeowners drawing from aquifer 110QPLC. This checklist gathers facts from local groundwater data and related considerations to help approach that sizing decision confidently.
1. Sample Size and Well Count Behind Area Water Quality Data
Eight sample results from one distinct well define local data
The U.S. Geological Survey collected eight total dissolved solids (TDS) measurements between May 2014 and October 2023 in Pitt County’s aquifer 110QPLC, all from a single well sampled multiple times. This narrow sampling scope means regional statistics reflect repeat measures at one location rather than multiple well sites.
Small sample size limits broad representativeness
Because the data comes from one well only, the median and range for TDS indicate conditions at that site more than across all Pitt County wells tapping this aquifer. This suggests homeowners should test their own water before sizing.
2. Plumbing Material and Age Influence Water from Source to Tap
Source water quality differs from household plumbing impact
The TDS figures represent groundwater quality before it interacts with household plumbing. Materials like piping or fixtures, and their age, can alter water quality by causing staining, taste, or corrosion effects regardless of source water minerals.
Age of plumbing affects treatment needs
Older plumbing can increase the risk of issues like scale buildup or corrosion-related changes, which may require a system designed to handle these secondary effects separately from the raw well water conditioning.
3. Additional Commercial or Industrial Questions Not Typical for Households
Volume and continuous use considerations
Commercial operators often inquire about how treatment handles larger volumes and uninterrupted flow, which are less relevant in residential sizing but important for selecting grain capacity and regeneration cycles.
Regulatory compliance and monitoring frequency
Businesses must consider regulatory limits and testing frequency that go beyond household norms, influencing system choice and management more strictly than typical home use.
4. Interpreting Median and Range for Total Dissolved Solids as a Homeowner
Median TDS is 88.0 mg/L with range from 0.12 to 113.0 mg/L
The median figure indicates a typical dissolved solids level around 88 mg/L at this well, with observed variability spanning very low up to modestly higher levels. These numbers suggest generally low mineral content compared to many other aquifers.
No sample exceeded federal TDS thresholds
Within these eight samples, none surpassed any federal limits for TDS. This confirms no regulatory exceedance was measured in the area, though TDS above certain secondary standards can affect taste or cause minor staining.
5. Influence of Sample Depth, Well Depth, and Source Type on Expectations
Sampling depth at 11 feet reflects shallow aquifer conditions
These samples were taken from 11 feet below ground level, representing very shallow groundwater data. Deeper household wells may encounter different water chemistry values, so homeowners with deeper wells should consider tailored testing.
Well construction and source type affect water clarity and chemistry
Different well depths and construction types can change exposure to minerals and contaminants. The shallow well sampled here may not fully represent deeper or artesian sources used by some residents.
6. What Not to Conclude From Pitt County Aquifer Data
- These area results do not specify the TDS level in your personal well.
- Detection of dissolved solids does not imply any safety or compliance issues.
- The small number of samples from only one well limits how broadly these numbers apply to all Pitt County homes.
- Water treatment sizing should rely on your well’s own lab test for the best system fit.
For effectively managing complete well water treatment, a system such as the Autotrol Complete Well System with 32,000 grain capacity ships ready to configure and can handle a wide range of dissolved solids conditions commonly found in residential settings. Pairing local data insight with your own water analysis will help select the right treatment size that meets your household needs.
Where this information comes from
Source: USGS groundwater sampling. Sampled 2023-10-31. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.
On record: U.S. Geological Survey sampling of Total dissolved solids in the 110QPLC aquifer (Pitt County): 8 results from 1 wells, median 88.0 mg/L, range 0.12-113.0 mg/L; none above any federal threshold
- ✓ 90-Day Money-BackNo restocking fees — return within 90 days.
- ✓ Manufacturer WarrantyGenuine Fleck · Pentair · VIQUA equipment.
- ✓ Free Expert SizingTalk to a specialist and buy the right system the first time.