Complete Well Water And Chlorination System
Pricing: request a quote
Get a Quote✓ Free shipping in the USA · ✓ 90-day returns · ✓ Secure checkout
What Government Sampling Reveals About Water Acidity in Jackson County
The U.S. Geological Survey has sampled groundwater from five wells within Jackson County's aquifer 120FLRD between 2011 and 2025, measuring pH levels to indicate water acidity. These wells, ranging in depth from 115 to 234 feet, consistently showed pH values between 7.1 and 8.1 standard units, with a median pH of 7.3.
Since the Environmental Protection Agency's secondary standard for pH—focused on aesthetics and corrosivity rather than health—is 6.5 to 8.5 standard units, none of the sampled results indicated acidic water in this range. This sampling does not represent any individual water source but provides an overview of typical pH conditions in the aquifer supporting homes throughout Jackson County.
Why pH Matters for Household Water Treatment
Water pH describes how acidic or alkaline the water is. Acidic water, below 7.0 pH, can be corrosive, potentially impacting plumbing, fixtures, and water quality over time. Even within EPA's acceptable pH range, slight acidity can accelerate corrosion, while elevated pH can affect taste and cause scaling. For homeowners, understanding pH is essential to select and size appropriate treatment solutions to protect plumbing and improve water quality.
Why Individual Testing Is Important
Although government data shows that groundwater in Jackson County’s aquifer tends not to be acidic, water conditions can vary significantly from one well to another. Factors like local geology, depth, and well construction influence pH at your home. To confirm if acidic water is an issue, testing your own water for pH and corrosivity indicators is necessary.
Sizing Whole-Home Treatment for Acidic Water
When a household confirms acidic or corrosive water, selecting the right treatment equipment size ensures effective correction and protection throughout the home water supply. Key criteria for sizing include the household’s water demand and flow rates, as well as the treatment capacity needed to adjust pH and neutralize acidity.
The documented solution designed for acidic water management is the Total Well — Complete Chlorination Whole-Home System. It utilizes chemical feed technology to address acidity and improve water quality on a continuous basis. This system ships ready to configure, with a tank size of 10 by 54 inches, a grain capacity of 48,000, and a maximum flow rate of 9 gallons per minute (gpm), capable of handling up to 17 gallons per day.
Matching System Capacity to Household Needs
- Grain Capacity: Reflects how much treatment media is available to manage water quality before regeneration or replenishment is necessary.
- Flow Rate (gpm): Determines how the system performs at peak household water use, ensuring water is treated effectively without pressure loss.
- Gallons Per Day (gpd): Indicates overall treatment volume supported by the system, important for daily water consumption rates.
Properly matching these specifications to your household’s water use patterns and confirmed water acidity levels helps optimize performance and extend equipment lifespan.
Next Steps for Homeowners Considering Acidic Water Treatment
To proceed confidently, have your water tested for pH and other corrosivity markers. This check clarifies whether acidic conditions exist at your site and their severity. Based on those results, selecting and configuring a chemical feed water treatment system sized correctly for your home's water demand can protect plumbing and improve water quality.
The Total Well system offers an established, durable approach for acidic water management by integrating chemical feed technology with suitably scaled equipment capacity. It addresses acidity consistently and comprehensively in residential settings supported by aquifer 120FLRD.
Where this information comes from
Source: USGS groundwater sampling. Sampled 2025-09-24. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.
On record: U.S. Geological Survey sampling of pH in the 120FLRD aquifer (Jackson County): 25 results from 5 wells, median 7.3 standard units, range 7.1-8.1 standard units; EPA secondary standard for pH is 6.5-8.5 (aesthetic/corrosivity, not health-based); 0 of 25 sampled results fell below 6.5