If You Wonder What Detected, Median, and Range Indicate in Yalobusha County’s Water Record
The U.S. Geological Survey has sampled groundwater from aquifer 124SPRT in Yalobusha County using wells 33 to 120 feet deep. Their testing from 2011 to 2022 detected pH levels in eight samples from three separate wells. In this context, ‘detected’ means the instrument measured pH in all cases; no sample was below the detection threshold. The median pH value was 6.2 standard units, representing the middle point of results. The range of values ran from 5.0 to 7.4 standard units, showing variation across locations and times.
If You’re Comparing Yalobusha County’s pH Data with Nearby Counties
When examining pH data from Yalobusha County alongside neighboring counties, it’s important not to overinterpret differences. Regional variations can arise from local geology, well depth, and sampling times. However, these comparisons reflect area-wide tendencies, not specific household conditions. A difference in median or range between counties does not predict the exact pH level of your household’s water without direct testing.
If You Need to Know Why Secondary Aesthetic Standards for pH Differ from Health-Based Limits
The Environmental Protection Agency sets a secondary standard for pH between 6.5 and 8.5 standard units. This threshold addresses water’s taste, staining potential, and corrosivity—not health risks. In Yalobusha County, five of eight samples fell below this range, indicating a tendency toward acidic water that may impact plumbing and appliances over time. This secondary standard is advisory and does not imply a health violation or unsafe condition.
If You Recognize That Plumbing Materials and Age Affect Water pH Independently of Source Water
Water pH measured at your tap may differ from source water due to interactions with plumbing materials and pipe age. Corrosion or chemical changes inside pipes can alter water chemistry, sometimes lowering pH independently of aquifer conditions. This means acidic water concerns in your home could partly reflect your plumbing system as well as the source aquifer.
If You Want to Understand What a Certified Laboratory Test of Your Water’s pH Will Report
A certified lab test on your household water sample reports pH as a numeric value reflecting its acidity or alkalinity at the time of sampling. This precise measurement informs how your water compares to both government secondary standards and local aquifer tendencies. Such testing is the essential step to determine your own water’s acidic condition rather than relying on regional data alone.
If You Wonder What the Measured pH Range in Yalobusha County Means Against Federal Guidelines—and What It Does Not
The pH range of 5.0 to 7.4 standard units found in area wells shows the presence of mildly to moderately acidic water in aquifer 124SPRT. This range crosses below the EPA’s secondary standard of 6.5, suggesting a potential aesthetic concern for some users. However, it does not constitute a safety violation or a health limit. Your household’s actual water pH may be higher or lower, so direct testing is necessary to assess treatment needs.
For homes confirmed to have acidic water, the Fleck Acidic / Low-pH Water Filter ships ready to configure for neutralizing acidity and protecting plumbing integrity.
Summary: This decision guide reviewed the meaning of regional pH sampling results, their limits in predicting household water acidity, and the difference between aesthetic and health standards. Testing your own water sample is the definitive way to assess acidity and determine if treatment like the Fleck System is appropriate.
Where this information comes from
Source: USGS groundwater sampling. Sampled 2022-05-04. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.
On record: U.S. Geological Survey sampling of pH in the 124SPRT aquifer (Yalobusha County): 8 results from 3 wells, median 6.2 standard units, range 5.0-7.4 standard units; EPA secondary standard for pH is 6.5-8.5 (aesthetic/corrosivity, not health-based); 5 of 8 sampled results fell below 6.5
- ✓ 90-Day Money-BackNo restocking fees — return within 90 days.
- ✓ Manufacturer WarrantyGenuine Fleck · Pentair · VIQUA equipment.
- ✓ Free Expert SizingTalk to a specialist and buy the right system the first time.