Fleck Acidic Water + Hard Water (Well) System

Buy Now

View full details

1. What 'detected', 'median' and 'range' mean in the sampling record on this page

The U.S. Geological Survey has sampled groundwater from 80 wells in Shelby County’s aquifer 124MMPS between August 2010 and June 2026, gathering 483 pH results. The term 'detected' means that pH was measured at all sampling points; none were below the instrument’s reporting limit. 'Median' is the middle value, 6.3 standard units, showing the central tendency among samples. 'Range' shows the spread: pH values from 4.9 up to 8.1 standard units. This range indicates that some groundwater sources in the area are acidic (below 7), while others are neutral to slightly alkaline. These figures reflect area-wide data and do not describe your household’s water specifically.

2. The household or facility symptoms that do and do not point to this problem

Acidic water (low pH) combined with hardness can cause noticeable household issues. You might observe metallic taste or a slight sourness, along with mineral deposits on fixtures or inside appliances. Hard water contributes to scale buildup in pipes and water heaters, reducing efficiency and lifespan. However, noticing scale alone does not confirm acidic water, nor does acidic water always produce strong symptoms. Water staining or corrosion signs might also relate to plumbing materials or age rather than just water quality. To pinpoint acid and hardness effects, consider laboratory testing of your water.

3. How the treated water differs at the tap once the documented technology is in place

Using a Fleck Acidic Water + Hard Water (Well) System modifies water properties by neutralizing acidity and reducing hardness. After treatment, water typically feels softer, reducing scale deposits and improving appliance longevity. The system is rated at 32,000 grain capacity, meaning it can handle substantial hardness before regeneration is needed. You can expect improved taste and less mineral buildup, which benefits plumbing and extends comfort in daily water use. The system ships ready to configure for straightforward setup.

4. What a certified laboratory test for this constituent reports and how to read it

A certified lab test for pH reports the water’s acidity or alkalinity on a scale typically from 0 to 14 standard units, with 7 as neutral. Values below 7 indicate acid water, and values above 7 indicate alkaline water. The report includes precise pH values measured under controlled conditions. It may also report hardness levels separately, usually in grains per gallon or mg/L as calcium carbonate. Interpreting these results helps determine if treatment for acid and hardness is needed for your household water.

5. What the measured range means against the relevant federal standard, and what it does not mean

The Environmental Protection Agency’s secondary standard for pH ranges from 6.5 to 8.5 standard units, intended to manage aesthetic and corrosivity concerns, not health risks. In Shelby County, 281 of 483 samples fell below 6.5, indicating that acidic conditions are common in this aquifer area. However, a measurement below 6.5 is not a violation or a health violation; it only suggests potential for corrosion or taste issues. This area data does not establish that every well or household water in Shelby County has low pH or a hardness problem. Actual water quality varies by location, depth, and other factors.

Closing: What you should NOT conclude from area data

Area-wide sampling from aquifer 124MMPS shows typical pH levels and their variation but does not determine the pH or hardness of your household water. Detecting acidity or hardness in regional data is not a direct indicator of your water’s condition. Only a current, certified laboratory test of your own water can establish its specific acidity and hardness levels. If you face household symptoms consistent with acid and hardness, testing is the necessary step before considering treatment options such as the Fleck Acidic Water + Hard Water (Well) System.

Where this information comes from

Source: USGS groundwater sampling. Sampled 2026-06-18. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.

On record: U.S. Geological Survey sampling of pH in the 124MMPS aquifer (Shelby County): 483 results from 80 wells, median 6.3 standard units, range 4.9-8.1 standard units; EPA secondary standard for pH is 6.5-8.5 (aesthetic/corrosivity, not health-based); 281 of 483 sampled results fell below 6.5