If your well taps shallow groundwater like the sampled 42-foot depths, expect similar iron levels but test to confirm
The U.S. Geological Survey sampled groundwater from wells in Hillsborough County's aquifer 112DELT at about 42 feet deep. The iron concentrations found ranged from 2000 to 2600 micrograms per liter (µg/L), with a median of 2150 µg/L. These samples reflect the area’s shallow groundwater but do not establish the exact iron concentration in your own well. Iron levels can vary significantly with well depth and source, so a test of your specific water is necessary to know your situation precisely. While these figures do not indicate any federal exceedance, they provide a starting point for sizing treatment to address iron-related issues alongside hardness.
If your household uses typical daily water volumes, align treatment capacity with your peak and average demand
Water treatment sizing depends on your household's water use and the concentration of iron and hardness in your supply. The documented Autotrol Iron + Hard Water (Well) System is rated for 32,000 grains capacity, meaning that it can handle a certain volume of hardness and iron removal before regeneration or maintenance is required. To select the right size, calculate your daily water consumption in gallons and consider the iron and hardness levels detected in your well. Balancing capacity with expected demand ensures efficient operation without undersizing, which can reduce effectiveness, or oversizing, which can waste resources.
If you consider the government-measured iron range for aquifer 112DELT, know these are not legal limits or safety violations
The range of iron detected—2000 to 2600 µg/L—falls below any federal maximum contaminant levels for iron in drinking water, as iron is regulated mainly for aesthetic concerns such as taste, staining, and color. Detection is not a violation or indication of unsafe water by itself. For hardness, regional data from this aquifer is not specified here, but hardness affects water hardness grain calculations, influencing system capacity choices. Understanding that these measurements are regional helps avoid misinterpreting your well water quality without a direct test.
If you have laboratory testing for iron and hardness, interpret results based on accurate units and treatment thresholds
A certified water laboratory report for iron will list concentrations typically in micrograms per liter (µg/L) or milligrams per liter (mg/L). Knowing your exact iron concentration helps refine treatment sizing. Hardness is often reported in grains per gallon (gpg) or mg/L as calcium carbonate. These values combined inform how many grains your equipment needs to handle, guiding the right Autotrol System selection. Without this data, sizing estimates rely on area medians and ranges only, which may not be precise for your water.
If you want to narrow down causes of water quality issues, follow a sequence from simple to detailed checks
Begin with visual and taste observations, checking for staining, discoloration, or hardness effects on your household water. Next, test for iron and hardness with home test kits or local laboratory services. Comparing those results with regional data lets you see if your water fits the expected range for aquifer 112DELT. If concentrations are within typical ranges, sizing the treatment as per your water use helps target efficient iron and hardness management. Following this stepwise approach ensures cost-effective assessment and treatment decisions.
Summary: Hillsborough County households drawing water from aquifer 112DELT can reference area iron data showing a median 2150 µg/L iron level in shallow wells. This regional information helps frame expectations but does not replace a specific water test. Treatment sizing should consider your household’s daily water demand and the combined iron and hardness content, guiding the choice of a 32000 grain-capacity Autotrol Iron + Hard Water (Well) System that ships ready to configure. Correct sizing optimizes performance in managing iron and hardness for cleaner water and better appliance longevity.
Where this information comes from
Source: USGS groundwater sampling. Sampled 2016-05-23. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.
On record: U.S. Geological Survey sampling of Iron in the 112DELT aquifer (Hillsborough County): 4 results from 1 wells, median 2150.0 ug/L, range 2000.0-2600.0 ug/L; none above any federal threshold
- ✓ 90-Day Money-BackNo restocking fees — return within 90 days.
- ✓ Manufacturer WarrantyGenuine Fleck · Pentair · VIQUA equipment.
- ✓ Free Expert SizingTalk to a specialist and buy the right system the first time.