Fleck Corrosive Water Damaging Pipes Filter

Buy Now

View full details

Water in Mono County commonly comes from deep aquifers ranging from 405 to 1300 feet below ground. This water travels through natural underground formations, eventually reaching wells that supply households. Understanding the water quality in this aquifer is essential for managing issues such as corrosive water and preventing damage to plumbing.

How Water Treated by the Fleck System Differs at the Tap

When corrosive characteristics affect water, pipes and fixtures can experience accelerated wear and corrosion. The Fleck Corrosive Water Damaging Pipes Filter is designed to reduce the effects that cause damage inside household plumbing systems. Once the Fleck System is configured for your use, the water passing through your taps tends to be less aggressive to pipe metals. This helps extend the life of plumbing by managing the chemistry that leads to corrosion, contributing to a healthier flow and fewer leaks or rust stains.

Reading the Chloride Concentrations in Mono County Aquifer Sampling

The U.S. Geological Survey collected 240 chloride measurements from 19 separate wells in the Mono County aquifer area between April 2012 and November 2022. These wells were between 405 and 1300 feet deep. The median chloride concentration found was 10.25 mg/L, with a range from 0.24 mg/L to 32.9 mg/L. All results were below federal thresholds for chloride concentration, indicating no legal exceedance or health-based violation in this aquifer.

Chloride concentration is important because elevated chloride levels can contribute to water corrosivity, which can accelerate pipe deterioration and cause metallic tastes or staining. The median value helps represent a typical chloride level, while the range shows how much this level can vary naturally across different wells and times in the area.

Maintenance Rhythm of the Fleck Corrosive Water Damaging Pipes Filter

The Fleck System is designed for household use and ships ready to configure. It requires routine maintenance to continue managing corrosive effects effectively. Maintenance typically involves periodic checks of filter media condition and system operation, which can be done based on manufacturer guidelines or water quality changes. Regular attention ensures the system continues to reduce corrosive impact on plumbing.

Understanding 'Detected,' 'Median,' and 'Range' in the Sampling Record

• Detected: Chloride was measured in every sample taken, indicating presence but not implying a problem by itself.
• Median: The midpoint concentration value across all samples, helping to understand the central tendency of chloride levels.
• Range: The lowest to highest measured chloride levels, showing natural variability in the aquifer.

Detection of chloride is routine and expected, and none of the samples exceeded federal chloride standards. Detected chloride does not mean the water is unsafe or in violation of any standard.

What You Should Record Before Seeking Treatment Advice

To understand your own water and get the best advice, have these details ready:

• Results from a current water test specific to your household supply, especially including chloride and pH measurements.
• Information about any existing equipment managing water quality.
• Observations of any plumbing issues such as staining, leaks, or metallic taste.

Only a test of your own water can confirm its composition; regional data helps guide expectations but does not replace household testing.

How This Problem Differs From Other Common Water Issues

Corrosive water is due to chemical aggression that can damage pipes over time, often involving factors such as low pH or high chloride. This differs from hard water, which primarily relates to calcium and magnesium causing scale buildup. It also differs from sediment problems, which involve particles causing cloudiness or clogging but do not chemically attack pipes.

Recognizing the specific cause of plumbing issues helps select the right treatment approach. In Mono County, chloride levels contribute to corrosive potential but do not alone define water hardness or sediment presence.

The Key Test to Clarify Your Household Water Corrosivity

The most informative test to order is a corrosion profile that measures chloride, pH, alkalinity, and other parameters related to water aggressiveness. These results will confirm whether the water’s corrosivity is significant enough to require intervention. With this test, you can determine if the Fleck Corrosive Water Damaging Pipes Filter is an appropriate solution to help protect your home's plumbing from corrosive damage.

Where this information comes from

Source: USGS groundwater sampling. Sampled 2022-11-17. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.

On record: U.S. Geological Survey sampling of Chloride in the aquifer (Mono County): 240 results from 19 wells, median 10.25 mg/L, range 0.24-32.9 mg/L; none above any federal threshold