If you notice water that seems more corrosive or causes unexpected wear on your plumbing fixtures over time, your household might be dealing with acidic water. In Caddo County, Oklahoma, the local aquifer 313RSPG has been sampled to provide insight into typical pH levels, helping residents determine what class of water treatment is appropriate.
If acidic water is untreated for years, what can you expect?
When water with a lower pH remains untreated, it can cause gradual deterioration of plumbing materials like pipes and faucets. This process happens because acidic water tends to react with metals, slowly increasing leaching and leading to potential taste issues or discoloration in water. However, it's important to understand that corrosion effects develop over extended periods and depend on individual water chemistry.
If your water source depth varies, how does that affect expected water acidity?
Sampling in Caddo County's aquifer 313RSPG included wells ranging from 120 to 350 feet deep. Generally, deeper wells may show more stable pH levels, but local geology and well construction also influence water characteristics. In this aquifer, the sampled wells showed a range of pH values, illustrating that depth alone does not fully define acidity levels in household water.
If you review the sampling record terms 'detected', 'median', and 'range', what do they tell you?
The US Geological Survey recorded 13 pH samples from seven wells in this area between 2015 and 2017. All samples detected pH within the reporting limits, with no values below detection thresholds. The median pH was 7.1 standard units, and the range was 6.7 to 7.9 standard units. This means the water's acidity varied but stayed mostly neutral to slightly alkaline. These figures reflect conditions in the aquifer generally, not your specific household water.
If you compare EPA secondary aesthetic standards to health-based limits for pH, what is the distinction?
The EPA secondary standard for pH ranges from 6.5 to 8.5 standard units. This range is intended to address water aesthetics and potential corrosivity rather than health risks. None of the sampled results in Caddo County fell below 6.5, indicating water acidity did not reach levels generally associated with aesthetic concerns or high corrosivity. This standard should not be misinterpreted as a health safety threshold.
If you consider problems similar to acidic water, how do you differentiate them?
Acidic water is primarily indicated by pH below neutral levels. However, water quality issues like hardness or iron presence can sometimes cause similar symptoms such as staining or taste changes but do not involve pH changes. Testing for pH specifically distinguishes acidic conditions from these other common water concerns, allowing for targeted treatment decisions.
If you analyze the measured pH range against the EPA secondary standard, what can you conclude?
The measured range from 6.7 to 7.9 standard units falls well within the EPA secondary standard of 6.5 to 8.5. This means the aquifer water generally meets recognized aesthetic and corrosivity guidelines. It does not imply your household water will match these values exactly, as individual well conditions vary. Testing your own water's pH is essential before choosing a treatment method.
In summary, the Caddo County aquifer 313RSPG shows pH levels indicating mostly neutral to mildly alkaline water, with no sampling evidence of problematic acidity. Deciding on treatment depends on your own water test results and household observations. The Autotrol Acidic / Low-pH Water Filter ships ready to configure and offers a documented solution for acidic water when testing confirms the need.
Where this information comes from
Source: USGS groundwater sampling. Sampled 2017-06-07. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.
On record: U.S. Geological Survey sampling of pH in the 313RSPG aquifer (Caddo County): 13 results from 7 wells, median 7.1 standard units, range 6.7-7.9 standard units; EPA secondary standard for pH is 6.5-8.5 (aesthetic/corrosivity, not health-based); 0 of 13 sampled results fell below 6.5
- ✓ 90-Day Money-BackNo restocking fees — return within 90 days.
- ✓ Manufacturer WarrantyGenuine Fleck · Pentair · VIQUA equipment.
- ✓ Free Expert SizingTalk to a specialist and buy the right system the first time.