Many households in York County using complete well systems notice that their existing equipment struggles to keep pace with household water demand. At kitchen taps and bathroom fixtures, this can mean reduced flow or pressure during peak use times. Understanding the water quality in this area helps clarify what may be behind these challenges and how to approach effective treatment.
Understanding 'Detected', 'Median', and 'Range' in York County Aquifer Sampling
Detected means measurable amounts were found in samples but not necessarily a problem
U.S. Geological Survey data reports total dissolved solids (TDS) detected in all six samples taken from York County’s aquifer 112SRFD between 2011 and 2019. Detection indicates the presence of dissolved substances in the water but does not imply any health risk or regulatory violation.
Median TDS value summarizes the central tendency over multiple samples
The median TDS found was 164.0 mg/L. This value represents the midpoint concentration measured in the set and provides a useful benchmark for what typical TDS levels might be in this aquifer area.
Range shows variability between the lowest and highest monitored levels
The samples ranged from 0.24 mg/L up to 237.0 mg/L, reflecting natural variability in groundwater conditions among wells in this region, important to keep in mind when considering your own water.
Why Secondary Aesthetic Standards for TDS Differ from Health-Based Limits
Secondary standards govern taste, staining, and corrosivity rather than health safety
For TDS, federal guidance sets aesthetic secondary standards that concern water appearance and household effects, not health risks. None of the samples exceeded any federal health-based threshold, highlighting that detected levels here are not a safety concern.
Aesthetic factors can impact appliance longevity and water taste
Higher dissolved solids can cause mineral deposits or alter taste perception, influencing treatment decisions based on household preferences and equipment maintenance needs rather than health mandates.
Checklist for Ruling Out Causes of Water Supply Limitations
Check household water use patterns
Begin by observing times of peak water use and fixture flow rates to identify if supply issues relate to demand exceeding equipment capacity.
Evaluate pressure and flow with pressure gauges
Monitoring static and dynamic water pressure helps determine if mechanical or supply constraints are involved.
Assess equipment capacity against daily water consumption
Compare your measured household water needs to the grain capacity and flow rates of existing equipment to judge if current resources suffice.
Collect a certified laboratory test of your own well water
Since area data does not specify your well, a lab test for TDS and other constituents provides a precise picture of your water quality.
Comparing York County’s TDS Record with Neighboring Areas
Recognize the scope and depth of samples
Sampling here involved a single well 45 feet deep with six measurements over eight years. Adjacent counties may have different data scopes and ranges, so direct comparisons should note these context differences.
Avoid assuming uniform water quality across counties
Natural variations in geology mean that TDS levels can differ significantly even between nearby aquifers, so treatment decisions should rely on local testing rather than regional generalizations.
Interpreting a Certified Laboratory Test for TDS
Look for TDS reported in mg/L (milligrams per liter)
Your lab report will list TDS concentration as a numeric value, reflecting dissolved mineral content in the water.
Compare results to aesthetic and health-based guidelines
Use federal secondary standards for TDS to gauge impact on taste and household equipment, while confirming no health-based limits are exceeded.
Review related water chemistry parameters if available
Additional tests for pH, hardness, or specific ions help build a comprehensive understanding of water treatment needs.
For York County households whose existing equipment cannot keep pace with water demand, the Fleck Complete Well System ships ready to configure with a 32000-grain capacity to meet larger household requirements. Its documented performance aligns well with managing the flow and treatment demands reflected in this area’s aquifer profile.
Where this information comes from
Source: USGS groundwater sampling. Sampled 2019-07-24. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.
On record: U.S. Geological Survey sampling of Total dissolved solids in the 112SRFD aquifer (York County): 6 results from 1 wells, median 164.0 mg/L, range 0.24-237.0 mg/L; none above any federal threshold
- ✓ 90-Day Money-BackNo restocking fees — return within 90 days.
- ✓ Manufacturer WarrantyGenuine Fleck · Pentair · VIQUA equipment.
- ✓ Free Expert SizingTalk to a specialist and buy the right system the first time.