Understanding the Local Aquifer and Water Delivery
The water supplying homes in FIPS 110, Connecticut, commonly originates from the 112DFSF aquifer. This groundwater source, accessed by wells ranging from 10 to 155 feet deep, contributes water that then travels through household plumbing to taps. Regional groundwater sampling by the U.S. Geological Survey offers insight into characteristics relevant to water quality, including factors influencing corrosivity.
Distinguishing Public Records from Private Well Testing
Data collected by public agencies, such as the U.S. Geological Survey, represent area-wide aquifer samples rather than individual household wells. These results reflect a set of 24 measurements from 20 wells sampled over several years, not the specific condition of any one home’s water supply. While regional data provide valuable context, only a dedicated test of your specific well water can determine its precise composition and corrosivity potential.
Source and Presence of Chloride in the Region's Groundwater
Chloride is a naturally occurring constituent that enters groundwater through natural mineral deposits and can be influenced by environmental factors and human activity. In the Connecticut 112DFSF aquifer, chloride was detected in all sampled wells. Chloride contributes to water chemistry changes that can promote corrosive effects within plumbing, affecting pipe materials over time.
The Significance of Chloride Levels Compared to Federal Guidance
Regional chloride concentrations ranged widely from 1.47 to 875.0 mg/L, with a median of 66.65 mg/L. The federal secondary standard for chloride is set at 250 mg/L, an aesthetic threshold that addresses taste, staining, and corrosivity rather than health risks. Four samples exceeded this level, indicating potential for aesthetic concerns, but this does not imply unsafe or non-compliant water. Importantly, detection or exceeding this threshold does not alone define corrosivity severity in an individual household.
How the Autotrol Corrosive Water Damaging Pipes Filter Mitigates Effects
The Autotrol Corrosive Water Damaging Pipes Filter is designed to address corrosivity issues by neutralizing factors that degrade plumbing materials. This system conditions water to reduce its potential to harm pipes, extending their functional lifespan and maintaining water quality within the home. It ships ready to configure, providing a direct purchase option to consumers weighing treatment approaches for corrosive water.
Variation in Chloride Measurements Over Time
The USGS data cover nearly six years, from September 2011 to September 2017, showing chloride levels fluctuating within the broad observed range. Such variation highlights the influence of temporal changes in groundwater chemistry, affected by factors like seasonal recharge and localized conditions. Homeowners should expect water quality to vary over time and consider periodic testing to track their own well’s status.
Aesthetic Secondary Standards Versus Health-Based Limits
The federal secondary standard for chloride focuses on aesthetic factors such as taste and staining potential. It is distinct from health-based primary standards, which regulate contaminants posing direct risks to human health. Exceeding the secondary standard indicates that water may be unpleasant or cause minor damage to plumbing but does not indicate a health threat or legal violation.
Recommended Testing for Decisive Household Assessment
To accurately understand corrosive water risk at your residence, order a comprehensive water test that includes chloride concentration and corrosivity indicators such as pH and alkalinity. The result will clarify whether your water falls within ranges likely to cause pipe damage or aesthetic issues and will guide selection of appropriate treatment. This testing is essential to determine if the Autotrol Corrosive Water Damaging Pipes Filter or another measure is warranted for your household.
Where this information comes from
Source: USGS groundwater sampling. Sampled 2017-09-05. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.
On record: U.S. Geological Survey sampling of Chloride in the 112DFSF aquifer (FIPS 110): 24 results from 20 wells, median 66.65 mg/L, range 1.47-875.0 mg/L; 4 above an AESTHETIC secondary standard only (secondary standard 250.0 mg/L (aesthetic)) - not a health finding
- ✓ 90-Day Money-BackNo restocking fees — return within 90 days.
- ✓ Manufacturer WarrantyGenuine Fleck · Pentair · VIQUA equipment.
- ✓ Free Expert SizingTalk to a specialist and buy the right system the first time.