1. Interpreting Sulfide Concentrations Reported for Lake County's Aquifer 110QRNR
Median sulfide level is 0.014 mg/L
The U.S. Geological Survey measured sulfide in three area wells, finding a median value of 0.014 milligrams per liter. This number reflects the middle value of sulfide concentrations reported, not your home's water.
Range from 0.004 mg/L to 0.7 mg/L in sampled wells
The sulfide levels found vary across sampled wells, from as low as 0.004 mg/L to a higher reading of 0.7 mg/L. This range indicates natural variability within this aquifer near the surface at depths between 11 and 18 feet.
All results are below federal thresholds for sulfide
None of the measurements exceeded any federal limits. Detection of sulfide does not mean water violates safety standards, only that the compound is measurable in these wells.
2. Identifying Household Indicators Consistent with Sulfur Smell Problems
Presence of a rotten-egg odor in water
When water emits a distinct sulfur or rotten-egg smell, sulfide might be a cause, although exact cause and intensity depend on the specific water source.
Absence of corrosion or staining related to sulfide
Sulfide generally does not cause staining or corrosion. Presence of such signs could indicate other issues unrelated to sulfide odor.
Smell noticeable when water is drawn from taps or fixtures
The sulfur-like odor typically becomes evident when water is running, especially in hot water, as sulfide releases hydrogen sulfide gas.
3. Changes You Can Expect in Tap Water After Using a Fleck Rotten-Egg Sulfur Smell Filter
Reduction or elimination of sulfur-based odors
The Fleck System targets molecules responsible for rotten-egg smells, reducing or neutralizing them before water reaches faucets.
Water clarity and taste improvement
Filtered water typically tastes fresher and sharper in smell, with noticeable improvement in household water experience.
Maintenance-free operation with periodic servicing
The filter ships ready to configure and functions continuously, requiring no daily attention.
4. Comparing Lake County Sulfide Data with Neighboring Counties' Records
Variability in sulfide levels among adjacent aquifers
Other counties may show different median and range values, reflecting geological differences rather than better or worse water quality.
Regional patterns do not define individual household water quality
Comparison provides context but cannot substitute for a test of your own water source.
Government sampling focuses on shallow wells
Results pertain to wells around 11 to 18 feet deep; deeper wells may have different sulfide concentrations.
5. Differentiating Sulfur Smell from Commonly Confused Household Water Concerns
Not to be confused with metallic or chlorine odors
Sulfur smell is distinct from metallic tastes or chemical odors like chlorine; addressing the wrong issue can delay solving the real problem.
Separate from iron or manganese staining problems
Sulfur odor typically does not cause discoloration, unlike iron or manganese, which cause reddish or dark stains.
Odor without visible sediment or water discoloration
Sulfur smell often occurs with clear water and no particles; sediment issues point to different causes.
6. How the Fleck Rotten-Egg Sulfur Smell Filter Works to Remove Sulfur Odors
Adsorption of hydrogen sulfide gas
The system uses filtration media that chemically attract and hold sulfur compounds responsible for odors.
Oxidation and neutralization processes
It promotes reactions that convert sulfide compounds into non-odorous forms.
Consistent odor control at household water points
Once water passes through this Fleck System filter, sulfur odor is significantly reduced or eliminated at every tap.
Final Step: What You Should Test to Confirm the Need for Treatment
Order a laboratory sulfide test on a water sample from your own well or tap. A result above typical local concentrations may indicate a higher level of sulfide causing the smell. This test result will clarify whether a Fleck Rotten-Egg Sulfur Smell Filter is an appropriate solution for your household water.
Where this information comes from
Source: USGS groundwater sampling. Sampled 2012-07-18. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.
On record: U.S. Geological Survey sampling of Sulfide in the 110QRNR aquifer (Lake County): 3 results from 3 wells, median 0.014 mg/L, range 0.004-0.7 mg/L; none above any federal threshold
- ✓ 90-Day Money-BackNo restocking fees — return within 90 days.
- ✓ Manufacturer WarrantyGenuine Fleck · Pentair · VIQUA equipment.
- ✓ Free Expert SizingTalk to a specialist and buy the right system the first time.