Fleck Complete Well System

Buy Now

View full details

Ordering Your Approach: From Visual Checks to Laboratory Confirmation

When dealing with concerns about well water quality, especially for total dissolved solids (TDS), start with simple household observations. Look for visual signs such as staining on fixtures, unusual tastes, or scaling on appliances. These can indicate elevated dissolved solids but are not definitive. After ruling out plumbing issues or appliance malfunctions, consider professional laboratory testing. A lab test report for TDS will list the concentration in milligrams per liter (mg/L), providing a precise measurement of dissolved mineral content in your water. This step confirms the exact TDS level in your well, which can vary widely from regional averages.

The Impact of Fleck Complete Well System on Tap Water Characteristics

The Fleck Complete Well System is designed to reduce total dissolved solids to improve water taste, reduce scaling, and improve appliance lifespan. Once operational, treated water typically shows fewer mineral residues compared to untreated water. This system uses a grain capacity of 32,000, which allows it to handle the typical mineral load of a household well in Iron County efficiently. While it does not alter water safety, it enhances aesthetic qualities by managing dissolved solids known to affect staining and taste.

Additional Considerations for Commercial or Industrial Users Versus Homeowners

Commercial or industrial water users in the Iron County aquifer area add complexity beyond residential concerns. They need to consider process water standards, equipment compatibility, and regulatory compliance for discharge or product quality. These operators often require specific measurements and removal targets for dissolved solids based on their operational needs, which go beyond the household focus on taste and staining. Residential users primarily focus on comfort and appliance preservation, making household-scale treatment systems appropriate.

Seasonal and Multi-Year Changes Reflected in Government Sampling Data

U.S. Geological Survey data from three wells in Iron County, within aquifer 112SDGV, collected from July 2013 to September 2024, show TDS concentrations ranging from 0.16 to 166.0 mg/L. The median value across 18 samples is 120.5 mg/L. These samples reflect variability over more than a decade, showing that TDS levels can fluctuate seasonally or with changing groundwater conditions and well depths of 60 to 86 feet. This range highlights the importance of individual well testing rather than relying solely on regional data.

Interpreting 'Detected,' 'Median,' and 'Range' in the Regional Sampling Record

In the Iron County sampling record, 'detected' means total dissolved solids were measurable in all 18 samples. The 'median' is the middle TDS value in the data set, showing a typical concentration of 120.5 mg/L for the area. The 'range' indicates the lowest (0.16 mg/L) and highest (166.0 mg/L) concentrations found in the samples. Importantly, none of these results exceeded federal thresholds, meaning the concentrations noted are within acceptable aesthetic secondary standards. Detection alone does not signal a violation or safety issue but informs what residents might expect in their water depending on their specific well.

Example Interpretation for a Homeowner with a Well in Iron County

If you receive a lab result for your well's TDS, compare it to regional figures from the aquifer 112SDGV. Suppose your test shows a TDS concentration close to the median of 120.5 mg/L. In that case, your water's dissolved solids level aligns with typical regional groundwater quality. If it is near the upper range, you might observe more noticeable effects like minor scaling or taste changes, which the Fleck Complete Well System is equipped to address. Lower values indicate less dissolved mineral content but still benefit from understanding what dissolved solids are contributing to your water's characteristics.

Use these steps to precisely gauge your water quality concerns and determine when treatment is appropriate.

Summary: This page guided you through assessing your well water’s dissolved solids, beginning with straightforward checks and progressing to laboratory analysis, using government sampling data for context. It introduced how a household treatment system like the Fleck Complete Well System can improve water properties affected by total dissolved solids in Iron County.

Where this information comes from

Source: USGS groundwater sampling. Sampled 2024-09-11. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.

On record: U.S. Geological Survey sampling of Total dissolved solids in the 112SDGV aquifer (Iron County): 18 results from 3 wells, median 120.5 mg/L, range 0.16-166.0 mg/L; none above any federal threshold