1. Observing Seasonal and Multi-Year Variations in Total Dissolved Solids
Between September 2011 and September 2017, the U.S. Geological Survey collected 12 samples from three different wells in FIPS 160, Connecticut, all drawing from aquifer 112DFSF. These wells ranged in depth from 13 to 273 feet. The median measurement for total dissolved solids (TDS) was 62.0 mg/L, with individual samples ranging from 0.07 to 391.0 mg/L. This variation suggests that TDS levels in this aquifer can fluctuate widely over time and location, reflecting natural changes or influences on groundwater composition.
2. Understanding the Maintenance Rhythm of the Fleck System
The Fleck Complete Well System is engineered for continuous, reliable performance in residential well water treatment scenarios. Its maintenance schedule involves periodic checks of the system’s settings and resin condition, which aligns with treating up to 32,000 grains of dissolved solids. For households experiencing an increase in dissolved solids or greater water demand, following a regular rhythm of resin monitoring and regenerations based on water use ensures consistent quality without interruption.
3. Clarifying 'Detected', 'Median', and 'Range' in the USGS Sampling Record
The term "detected" in this record means total dissolved solids were measurable in every sample collected; none fell below the reporting limit, which is the minimum concentration the testing equipment can reliably quantify. The "median" is the middle value when all measurements are ordered numerically and reflects a central tendency in the data set. The "range" describes the lowest and highest recorded values measured in the aquifer during the given period and locations. These terms describe data scope and variation rather than individual well quality.
4. Judging Treatment Capacity Against Household Daily Demand
To control total dissolved solids effectively, it is important to relate treatment system capacity to household water consumption. The Fleck Complete Well System has a grain capacity of 32,000, a measure of the total solids it can remove before regeneration is needed. Households should estimate their daily dissolved solids load based on water usage and reported local concentrations to plan system regeneration timing. This approach avoids overburdening existing equipment, particularly when water use or TDS levels rise seasonally or over years.
5. Reading a Certified Laboratory Test Report for Total Dissolved Solids
A certified laboratory test for TDS will specify the concentration in milligrams per liter (mg/L), often alongside parameters like sample location and depth. The test confirms how much dissolved material—such as minerals and salts—is present in a well or tap sample. Evaluating this number against local aquifer data helps determine whether TDS levels fall within the typical range recorded by government monitoring and whether additional treatment is advised.
6. Comparing This Aquifer's Record to Neighboring Counties Without Overreading
Government data from neighboring counties may show different TDS medians and ranges due to differing geology, land use, and water sources. It is important to treat each area’s data as distinct; a higher or lower median in an adjacent region does not predict the reader’s well condition but offers context for natural variability. Avoid interpreting regional data as direct evidence of any single household’s water quality.
Conclusion
The key to managing complete well water treatment is to order a certified laboratory test specific to your household’s well water. This test will provide an accurate TDS measurement to compare with groundwater samples from aquifer 112DFSF. If concentrations are within or rising toward the upper range of area data, the Fleck Complete Well System, with its documented 32,000 grain capacity, offers a ready-to-configure solution designed to meet your household’s water treatment demands effectively.
Where this information comes from
Source: USGS groundwater sampling. Sampled 2017-09-08. These figures describe groundwater sampled in this area. They are not a test of any individual private well - only a test of that well can establish its own water.
On record: U.S. Geological Survey sampling of Total dissolved solids in the 112DFSF aquifer (FIPS 160): 12 results from 3 wells, median 62.0 mg/L, range 0.07-391.0 mg/L; none above any federal threshold
- ✓ 90-Day Money-BackNo restocking fees — return within 90 days.
- ✓ Manufacturer WarrantyGenuine Fleck · Pentair · VIQUA equipment.
- ✓ Free Expert SizingTalk to a specialist and buy the right system the first time.